PE Pipe Fitting
PE Pipe Fitting
Features
1.Our PE pipe fitting is designed with inert materialpolyethylene, which can resist corrosion. Exceptfor a few strong oxidants, this material can resist manychemical matters. There is no electronchemical corrosion and itdoes not needa corrosion proof layer.
2 There are no heavy metal additives in our PE pipe fitting for water supply, so it is non poisonous and not easily covered with dirt or contaminated bybacterium.
3. The smooth interior wall results in low friction coefficientand high flux of a fluid.
4. Our PE pipe fittings are so tough that they do notrupture if something heavy presses the pipes directly.
5. Using thermal fusion or electric fusion for water supply, no leakage ofthe pipe will occur as the connect point is distorted compared withrubber and other machinery connect points.
6. With its light weight and friendly operation, the PE pipe fitting is convenient for construction.
7. Our PE pipe fitting can be coiled with the flexibility of polyethylene and is used forno pipe tank construction. The layoutPE pipe fitting for water supply depends on the demand ofconstruction.
8. Our PE pipe fitting features good scratch resistance.
9. High ductility is another feature of PE pipe fitting forwater supply. Itsextension ration at break cannot exceed 500%. It has a strong ability to fit with pipe tank non-uniformsettling.
10. Our PE pipe fitting offers a long service life of morethan 50 years
Characteristics of Electro-fusion Connection
1. Our PE pipe fitting can be used for specializedelectron melt machine.
2. It is suitable for all pipes.
3. Used in different material pipe and pipe fitting.
4. Our PE pipe fitting generate no effect byenvironment or human behavior.
5. Low investment and low maintenance cost.
6. It is easy to operate andcontrol.
Characteristics of ButtWelding Connection
1. Our PE pipe fitting can be used for specializedthermal melt machine.
2. It is suitable for nominal outside diameter ofpipe, which is greater than 63 mm.
3. Our PE pipe fitting is suitable for differentmaterial pipe and fitting, pipe and pipe. The joint of different material pipe-to-pipe, pipe-to-fitting forsimilar characteristics of PE material should be tested before use.
4. It will effected by environment or human behavior.
5. High invest and maintaining cost.
6. The PE pipe fitting is only cost low forjoint.
7. An operator should be trained andexperienced.
Technical Specifications
| Name | Requirements | Test Parameters |
| Hydrostatic strength | No leaks, no failure≥100h No leaks, no failure≥165h No leaks, no failure≥1000h | 20℃,PE80:10.0MPa PE100:12.4MPa80℃,PE80:4.6MPa PE100:5.5MPa80℃,PE80:4.0MPa PE100:5.0MPa |
| Melt flow rate | Change in MFR by processing＜±20%1) | 100min |
| Min thermal stability | ≥20℃ | 200℃ |
| Cohesive resistance for electro fusion socket fittings | Length of initiation rupture in brittle failure≤L2/3 | 23℃ |
| Cohesive resistance for electro fusion saddle fittings | Rupture surface in brittle failure≤25% | 23℃ |
| Tensile strength for butt fusion fittings-spigoted fittings | Test to failure ductile: pass brittle: fail | 23℃ |
| Impact resistance of tapping tees | No leaks, no failure | 0±2℃ Mass of striker: (2500±20)g Height: (2000±10)mm |
| Mechanical Joints2) | ||
| Leak tightness under internal pressure | No leaks | 1h 1.5X |
| Leak tightness under internal pressure when subjected to bending | No leaks | 1h 1.5X |
| External pressure test | No leaks | 1h△P＝0.01MPa 1h△P＝0.08MPa |
| Resistance to pull out under constant longitudinal force | No pull-out or separation of the pipe from the fitting | 1h 23℃ |
1. Value as measured on the fitting relative to thevalue measured on the compound used.
2. Mechanical joints up to and including 63mm, test method for sizes greater than 63mm are under development.
Fundamental Performance of Material
| Item | Performance Requirements |
| Carbon black content1) | 2.5±0.5 |
| Carbon black dispersion1) | ≤ grade 3 |
| Pigment dispersion 2) | ≤ grade 3 |
| Min thermal stability (200°C) | ≥20 |
| g/10min Melting mass-flow rate 3), (5kg, 190°C) | The deviation from standard value of product should be less than ±25％ |
1. Only applicable for black pipes.
2. Only applicable for blue pipes.
3. Only applicable to compound.
Material
Our PE pipefitting is made of 100% pure PE80 orPE100 raw material.
Packaging
Standard exporting package is used.
Note
HSHS codeis 39174000.
Service
We value our clients and will provide advice, guidanceand other help in our effort to be of complete service. If necessary, we will send our technician to theclient's location and offer further training. Our clients can contact uson our service line at anytime if they have a problem with our products.
Zhongcai is a China-based PE pipe fitting manufacturer and supplier. We offer PE pipe fittings, window handle,embossing PVC profile and so on. Our high quality products are offered atcompetitive prices. We can completethe entire process of manufacturing PVC window, PVC sliding profile, etc. righthere in China. Our lower manufacturing cost saves yourpurchasing cost. More details on each ofour products are shown on the description page.
Links：https://globefindpro.com/products/107181.html
